How to Install a Tub (Step By Step).
How to Install a Tub (Step By Step).
Blog Article
We've stumbled on this post relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and believe it made perfect sense to relate it with you on this site.
Mounting a bathtub isn't specifically rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the project can move speedily; if you have to open up a wall to eliminate the old bathtub and position the new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the new one. Make certain you have actually certified on your own for the work and fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will certainly aid you install a new bathtub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to change the setup of your previous water pipelines.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the water. After doing so, activate the taps to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the restricted gain access to that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Making use of the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and also adjusting the feet on the bathtub up until the level reviews level.
To set up faucets, fit all-time low of the furthest versatile faucet adapter to the suitable supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water system and also examine all joints and new pipework for leaks and also tighten them if essential. Fill the bathtub and likewise check the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been used at least once as this will settle it right into its last setting.
Planning for the Installment
Firstly, the sustaining structure provided with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bath satisfies the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, creating the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and can securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealer can break fairly early if you do not think about this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the market. It is a good idea to fit the floor tiles using waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very drawn to How to Install a Bathtub and I really hope you enjoyed reading the new blog posting. In case you enjoyed reading our blog post please remember to share it. We take joy in reading our article about Tools You Need to Install a New Bathtub .
Book Report this page